5th International Congress on Chemical Engineering, دی ماه ۱۳۸۶

Accepted papers in 5th International Congress on Chemical Engineering

• A Regenerative Process for CO2 Removal and Hydrogen Production in Integrated Gasification Combined Cycle (IGCC) Processes

• Grafting of MMA onto Gelatinized and Dissolved Potato Starch in Aqueous Media

• Removal of heavy toxic metal ions from waste products by using chitosan

• A modified Thermodynamic model for prediction thermodynamic and rheological properties of polymer solutions

• A discussion about the effect of chemical treatment on the preparation of PET based activated carbon

• Method for increasing yield of single stage crystallizing N-vinylpyrrolidone

• Experimental Evaluation of The Effect of Pour Point Depressant On Lubricating Oils

• Vapor-liquid equilibrium in the aqueous systems containing poly(ethylene glycol) + sodium citrate and poly(ethylene glycol) + potassium citrate

• E-learning Strategies in Physical Chemistry

• Factors affecting the conversion and selectivity of ethylbenzene dehydrogenation over commercial catalysts

• On the Kinetics of Controlled/“Living” Radical Polymerizations Using Monte Carlo Method

• Induction Time of Reaction Crystallization of Silver Nanoparticles

• Gas Lift Design and Optimization in One of Central Iranian Oil Field

• Influence of enzymatic parameters on yield of carrot juice

• An LDA Study of Shear rate profiles of Rushton turbine in mixing tanks

• Model Comparison for Thermally Coupled Distillation Columns Developed for Optimization Objectives

• Investigation of Air Pollutants Due to Traffic in Zand Tunnel of Shiraz

• Examination the involving parameters in producing High molecular weight PVP in polymerization by H2O2 in aqueous solution

• Kinetic Evolution of Emulsion Polymerisation of Butyl Acrylate

• An extension of cubic equations of state to vapor-liquid-solid equilibria in asphaltene-toluene mixture and crude oil system

• Removal of VOC by Ozone on Platinum Catalyst: Effect of Temperature, Ozone Concentration and Pt Surface Area

• Application of microorganism effect of biological sludge of industrial sewage on microbial community of agricultural soil (health of soil and plant)

• Study of hydrogen separation from carbon monoxide using polyimide membrane

• Prediction of liquid-liquid equilibria of (n-hexane+methanol+water) ternary system in the temperature range of 278.15-328.15 K by Artificial neural networks (ANNs)

• New features of chemical engineering program in Iran

• Simulation of Heat Integrated Multi-effect Distillation Columns

• Investigation of Gel Rheology Used for Water Shutoff Treatment

• Investigation into Effective Agents on Purification of Crude Oil-contaminated Soil by Phytoremediation

• Removal of Aniline by a New Emulsion Liquid Membrane

• Adsorption isotherm of carbon dioxide on multi-walled carbon nanotube

• Study of Growth and Kinetic Modelling of Thiobacillus ferrooxidans

• TEG reconcentrator device modeling of Coldfinger natural gas dehydration process

• Protein Immobilization on Carbon Nanotubes as a Template for Drug Delivery Applications

• Application of biological sludge of petrochemical industry as an organic fertilizer for cultivation of plants

• Simulation of Modified Natural Gas Dehydration Processes

• Cost Estimation and Optimization of the Topping Unit Products in Khangiran Gas Refinery in the Steady State Condition

• Biosorption of copper﴾ІІ﴿ and chromium﴾VI﴿ from aqueous solutions by fungal biomass

• Using Polyethylene Glycol (PEG) Solution for Drying Gelcast Ceramic Parts

• Daily Gas Demand Load Forecasting for Tehran, Based on Artificial Neural Network

• New method for bioethanol production from waste wood

• Kinetics of Sulfate Ions Removal from Wastewater in Fixed Bed Column Using an Anion-Exchange Resin

• Case Study of Site Characteristic and Treatment Approaches for Cleaning a Hydrocarbon Contaminated Site in Iran

• Improving Indoor Air Quality Using Liquid Desiccant Heat Exchanger

• Bacterial leaching of a copper sulphide ore containing activated pyrite

• EFFECT OF SURFACE MODIFICATION ON OSMOTIC CONCENTRATION OF SUGAR SYRUP

• Emulsification of Heavy Crude Oil in Water For Pipeline Transportation

• Sulphur Coated Urea Process and Production

• Feedstock Effects on Selecting the Appropriate Coil Configuration for Cracking Furnaces

• COMBINED PHOTOCHEMICAL AND BIOLOGICAL PROCESSES FOR WATER AND WASTEWATER TREATMENT: AN OVERVIEW OF TRENDS, ADVANCES, AND FUTURE

• Comparison of sludge microbiological characteristics in Tehran Wastewater Treatment Plants

• Determination of the optimum conditions for extraction of furfural from sugarcane bagasse by Taguchi experimental design method

• Optimization of Chalcopyrite Concentrate Bioleaching using extremely Thermophilic Bacteria

• CO2 Solubility in 1-ethyl-3-methylimidazolium trifluoromethylsulfonate Using the Monte Carlo Simulation

• Chemorheology of Polymer Gel Filled by Inorganic Material Used in Gas Well Water Shutoff Treatments

• A method for computing of specific heat of compressed liquid of Nitrogen Tetroxide

• Developing a scaling equation as a function of pressure and temperature to determine the amount of asphaltene precipitation

• Optimization of Binary Interaction Coefficients of Wilson Equation in NMP-1, 3 Butadiene System

• Comparison of Biosurfactant Production by Four Pseudomonas aeruginosa Strains

• Numerical Study of Dynamic Two-Dimensional Heat and Mass Transfer for Hydrogen Storage in a Metal Hydride Bed

• Determination of Important factors on Bioremediation of Crude Oil Contaminated Soils

• A Moisture Transfer Model for Kenaf fiber Drying

• Modeling of Ethylene-oxide Catalytic Reactor

• Investigation of Biological Sludge of Industrial Sewage Effect on Properties and Structure of Agricultural Soil

• Using Gas Hydrates for Natural Gas Storage and Transportation

• Prediction of Plus Fraction Molecular Weight in Isothermal Hydrocarbon Reservoirs

• Use of sugar cane-molasses for production of biosurfactant by a partially characterized new Bacillus Species

• Catalytic Effect of Transient Metal Oxide Powders onto Reaction Rate of Methacrylic Acid-Based Gelcasting

• An efficient coupled Genetic Algorithm-NLP method for heat exchanger network synthesis

• Enzymatic production of biodiesel from canola oil

• Synthesis and catalytic properties of supported nano Perovskites on gamma alumina for CO oxidation

• Preparation of Epoxydiacrylate Coating and Optimization its UV-curing Conditions

• Real Component Substitute Mixture in Simulation of Petrochemical Processes

• Some investigations on microbial de-emulsification of water-in-oil emulsions

• Comparative study on extraction of Iranian Sweet lime (citrus .limettioides) essence using cold press and hydrodistillation method

• Bioleaching of a Smelter Copper Dust in a Continuous Series of Airlift Reactors

• Prediction of PVT Properties of Iranian Oil Fields Using Artificial Neural Networks

• The Study of Static Electromechanical Properties of Silicone Nanocomposites

• Isolation and identification of indigenous microflora degrading PCBs from a contaminated soil with transformer oil

• Simulation of Drying of Agricultural Products Using Countercurrent Moving Bed Dryer

• A review on Solution Techniques of Population Balance Model

• Recovery of Triethylamine from a waste of solvent mixture from an antibiotics production

• Mathematical Modeling and Simulation of Bandar Imam Petrochemical Company's (BIPC) Three Phase Polyvinyl chloride Degassing Column

• steam stripping, monomer removal, degassing, vinyl chloride.

• Study trend of Biodegradability of Phenolic Compounds during Photo-Fenton Advanced Oxidation Process

• Commercial Reactor Modeling of Slurry High-Density Polyethylene Process in Arak Petrochemical Complex

• Performance of Wastewater treatment Plant in Amol Industrial Park

• Modeling of Gas-Solid Reactions by Percolation Theory using a Mont Carlo Simulation Method

• Predicting Surface Tension of n-alkanes Using The Gradient Theory and SRK EoS

• Study on Sodium Fluoride Dimensions in UF6 & HF Chemical Traps

• Equilibrium Swelling Study of Cationic Acrylamide-Based Hydrogels in Aqueous Electrolyte Solutions

• Optimization of physico-chemical conditions for Mycodecolorization of Widely Used Textile Industry Azo Dyes

• Experimental investigation of biodiesel from castor oil: production and kinetics mechanism

• A Hydrodynamic Experimental Study of Slurry Bubble Column

• Isolation of Spearmint Leaves (Mentha Spicata L.(Labiatae)) Volatiles by Supercritical Fluid Extraction

• Modification of van der Waals Mixture Model By Chemical Theory

• Concentration of Carrot Juice using Osmotic Membrane Distillation Process

• Effect of functionalisation of multi walled carbon nanotube on detection of enzymatically generated thiocholine at carbon nanotube modified graphite electrode

• Particles trajectory simulation in closed horizontal channels by Eulerian-Lagrangian approach

• Use of Polyacrylamide Polymer Gel for Conformance Control in the Ahwaz-Asmari Reservoir Conditions

• Bioremediation of DSO contaminated soil in laboratory scale

• Kinetics Study of Hydrazodicarbonamide Synthesis Reaction

• Clarification of carrot juice with membrane and enzymatic processes

• Permeability and Porosity Changes due to Thermal Effect during Thermal Recovery in Reservoirs

• The Analysis of Fluid loss Properties under Dynamic and Static Conditions

• The New Single Step Synthesis of Phthalocyanine Green in Aqueous Sodium Cholride Solvent Using a Microwave Oven

• Study of Chemical Recycling of Poly (ethylene terephthalate) Waste

• Modeling of MMA Bulk Polymerization Reactor: Gel and Glass Effects

• Permeability of CO2 and O2 through chitosan membrane

• STUDY ON LYSINE FERMENTATIVE PRODUCTION BY CORYNEBACTERIUM GLUTAMICUM AND BREVIBACTERIUM FLUVUM

• An improved correlation for density of compressed liquid of Nitrogen Tetroxide

• Evaluation of fatty acids effects on apatite and iron oxides wettability and their prediction by fuzzy logic

• Effects of aging time and temperature on the precursors of Cu/ZnO/Al2O3 catalyst for methanol synthesis

• Adsorption of Polyethylene glycol with Various Molecular Weight on the Zinc Oxide Nanoparticle

• Cubic Equation of State Based on a Theoretical Derived Attraction Term for Prediction of Phase Behavior of High Pressure Gas Reservoirs

• CORRELATION OF BUBBLE GROWTH RATE IN SUPERHEATED METHANOL

• Production of Protopectinases by Bacillus subtilis

• Modeling and simulation of adiabatic fixed-bed reactor for the partial oxidation of methane to synthesis gas

• Enhancement of oxygen transfer and recombinant hG-CSF production in Pichia pastoris fed-batch fermentation

• Overall Mass Transfer Coefficients in a Hanson Extraction Column

• Estimation of carbon dioxide solubility in pure water :Comparison of phase equilibria results from theWong-Sandler combining rule with artificial neural network

• Effect of tray efficiency on dynamic behavior of distillation columns

• Effect of Surface Active Substances on the Operation of a Rectangular Bubble Column

• Stage Efficiency of Hanson Mixer-Settler Extraction Column

• A neural network approach for identification and modeling of delayed cocking plant

• Treatment of aqueous phenol with crude extracted potato and lamiaceae enzyme

• Separation and Recovery of Sulfuric Acid with TEHA

• Slip Velocity in a Liquid-Liquid Extraction Pulsed Packed Column

• Modeling and simulation of growth kinetics for recombinant E. coli BL21 (DE3) producing hIFN-γ in batch and fed-batch cultures

• Process Initiatives to Boost Ethane Recovery

• Catalytic Dehydration of Methanol to Dimethyl Ether (DME) at Various Temperatures with and without Presence of Water in Feed Stream

• Application of Neural Networks in Vapor-Liquid Equilibrium Estimation of Difluoromethane and 1,1,1,2-Tetrafluoroethane

• The Effect of Particle Size and Concentration ATH on Flammability and Mechanical Properties High Density Polyethylene and Ethyl vinyl acetate (HDPE/EVA) Compound

• The Effect of Organoclay on Curing Time of Elastomeric Nanocomposites Based on NR

• Optimization of Integrated Low-Temperature Gas Separation Processes using SA Method and Different Refrigerants

• Artificial intelligence estimation of vapor pressure

• Solvent Extraction of Zinc from Acidic Solution Obtained from Cold Purification Filter Cake of Angouran Mine Concentrate Using D2EHPA

• Applying Various Methods for Screening Biosurfactant Producers from Oil-degrading Microorganisms

• A New Approach to Solve Population Balance Equations in Chemical Processes

• Dispersed Phase Holdup in a Pulsed Packed Column in With and Without Mass Transfer Conditions

• Evaluation of the Recombinant Escherichia coli BL21(DE3) Growth Kinetics in Glucose-limited Chemostat Culture

• Heat Integration and Retrofit of Distillation Unit

• Prediction of mixing time in a bubbly two-phase stirred tank by optical method

• Effect of Cleaning Agent Concentration on Chemical Cleaning of Reverse Osmosis Membrane Fouled by Sugar Solution

• Use of Neural Network for Prediction of Minimum Miscibility Pressure

• Thermodynamic study of hydrogen reformer plant by minimization of Gibbs free energy

• Application of continuous polydisperse molecular thermodynamics for modeling asphaltene precipitation in crude oil systems

• New approach for the determination of Lennard-Jones' parameters and some transport properties of nitrogen and methane using P-V-T data

• Effect of temperature on the adsorption isotherms of carbon dioxide on activated carbon

• Modeling of supercritical Neem extraction from Neembin

• New Correlation For Point Efficiency In Distillation Columns

• Removal of H2S from Synthetic Waste Gas Streams Using a Biotrickling Filter

• Characterization of flooding in a pulsed packed column in with and without mass transfer conditions

• Dynamic mechanichal properties of biodegradable films based on chitosan and zein

• Pharmaceutical wastewater treatment using an airlift membrane bioreactor containing acetaminophen

• Biological oxidation of ferrous iron in an air-lift bioreactor

• Study of Components concentration effect on grafting of ferroelectric liquid crystal polymers

• An optimized fermentation process for recombinant human G-CSF production by Pichia pastoris fed-batch culture

• Experimental &Theoretical Investigation of Pressure Drop across Tube Bundle of a THPHE and Introducing a New Correlation

• Modeling of temperature gradients in packed-bed solid-state bioreactors

• Alkali-activated Binder from Blast-furnace Slag of Isfahan Steel Plant

• Modeling and simulation of methane autothermal reforming

• Synthesis and characterization of poly(ethylene terephthalate - co - 1,4 cyclohexylenedimethylene terephthalate)

• Acidity deterioration and coke deposition on Iron- Zeolite Catalyst in Fischer – Tropsch Synthesis

• Dynamic Optimization of Methanol Reactor

• Influence of mass transfer direction on the performance of pulsed packed column

• CFD Modeling of MTO process over SAPO-34 Catalyst in an isothermal fixed bed reactor

• Hydrate Kinetics: The Main Problem in the Gas Hydrate Industrialization

• Antioxidant activity of Iranian rice bran

• Effects of surfactant, initiator and temperature on conversion and particle size of styrene emulsion polymerization

• Enzyme immobilization on ordered mesoporous materials: Effect of pH and enzyme size

• Modeling of Coupled Heat and Fluid-Flow in a Fractured Block (Comparison between Variable Width Fracture and Constant Width Fracture)

• CFD Simulation of Heat Transfer from Finite Cylindrical Catalyst

• Application of Artificial Neural Networks for prediction of Natural Gas Mixtures Water Content

• Characterization of Flooding in a Hanson Extraction Column in With and Without Mass Transfer Conditions

• Temperature control in packed-bed solid-state bioreactors

• Simulation of urea prilling tower with rectangular sectional area

• Modeling of the absorption of acid gases into aqueous solutions of MDEA using discretization by the finite difference method

• Swelling Kinetics Modelling of Cationic Acrylamide-Based Hydrogels

• An NLP approach for evolution of heat exchanger networks designed by pinch technology

• Optimization of Cu/ZnO ratio in Cu-ZnO-ZrO2/H-Y bifunctional catalyst used for production of Tetrahydrofuran from Maleic Anhydride

• Preparation of Polymeric Membrane for pervaporation separation

• Hydrogen Network Retrofit in Oil Refineries (with Capital Investment Limitation)

• 2D Lattice Boltzmann Model Benchmarking for Low Reynolds Poiseuille Flow through Channel

• Oxidation of p-xylenes to terphthalic acids with O2/HNO3 in ionic liquids

• Effect of Diesel fuel additive on diesel engines

• Study on the effect of prepolymerization parameters on catalyst performance in propylene slurry polymerization using heterogeneous Ziegler natta catalyst

• Determination Effects of Process Variables on Nitrogen Production PSA System by Mathematical Modeling

• CO2 REDUCTION THROGH OPTIMIZATION OF STEAM NETWORK IN PETROLEUM REFINERIES

• Study of a Fungal Biofilter Treating Toluene Vapors during Intermittent Loading

• Comparision between TRAINLM and TRAINSCG Algorithms for modeling of the treatment of wastewater contaminated with methyl tert-butyl ether (MTBE) by UV/H2O2 process

• Preliminary evaluation of ozonation of methyl tert-butyl ether in the presence of perfluorooctyl alumina

• Ni-Cu-Cr Hydrotalcite-like compounds as precursors for acetone hydrogenation catalysts in gas phase

• The effects of temperature and pH on the phase equilibrium of aqueous two phase systems containing polyvinylpyrrolidone and K2HPO4 / KH2PO4 buffer: Experimental and modeling

• CFD simulation of PVC Fluidized Bed Dryer Hydrodynamic

• A generic model for prediction of separation performance of olefin/paraffin mixtures by glassy polymer membranes

• Direct synthesis of DME using a bifunctional catalyst: Type of reactor and catalyst performance

• Conversion of Methanol to Light Olefins over Dealuminated Mordenite: Selective Formation of Propylene

• Simulation of Tabriz refinery hydrocracker unit by artificial neural network

• Production of dissolving pulp (alpha-cellulose) from wastes of corn stalk

• Evaluation of carotenoid production in extremely halophilic prokaryotes isolated from Aran – Bidgol Lake

• Prediction of Asphaltene precipitation from live-oils

• Effect of water level on individual residence time distribution curve of traditional oil-water separator

• Study of an Iranian South-West Reservoir by Simultaneous Solution Method

• Porosity change during solid-state fermentation of Aspergillus niger in laboratory scale packed bed bioreactors

• Hydrocarbon Miscible Gas Injection in One of the Iranian Oil Reservoir: Experimental & Empirical Approaches

• Poly (hydroxybutyrate-co-hydroxyvalerate) production in a batch fermentation of cheap substrates with co-cultures of Propionibacterium shermanii and a Bacillus strain isolated from date syrup waste

• Feed Stuff Production from Methanol by Methylotrophic Microorganisms

• Relationships between morphology, swelling, mechanical properties of PDMS/PAAc sequential IPNs

• EXPERIMENTAL STUDY OF PROPANE HYDRATE FORMATION IN A LABORATORY FLOW LOOP

• Investigation of Loop Bioreactor for Production of Single Cell Protein (SCP) from Natural Gas

• Effect of Additives on Asphaltene Precipitation

• A Study on Ultra High Molecular Weight Polyethylene (UHMWPE) Gel Spinning

• Characterization of the plus fraction using distribution functions For Iranian gas condensate reservoir

• Reliability of Determination of the cation exchange capacity (CEC) of bentonites by methylene blue and copper ethylenediamine complex adsorption

• Influence of process variables on instability of crude oil-water emulsion

• An Investigation on the Sensitivity Analysis of the Parameters of Proposed Wax Precipitation Model

• Biological Copper Extraction from Copper Smelters Dust

• Simulation of Hyaluronic Acid Production by Streptococcus zooepidemicus in Batch and Fed-batch Cultures

• A neural network for predicting collection efficiency using genetic algorithm in venturi scrubbers

• Two Dimensional numerical simulation of turbulent flow in a mixing layer using Transport Element Method

• Optimization of suspension polymerization process conditions for reducing of SAN fine particles using Taguchi method

• Simultaneous Prediction of Critical and Sub-critical Phase Behavior of Binary Mixtures Using Cubic Equations of State

• Effect of operating conditions on oxidative coupling of methane over Mn/Na2WO4/SiO2 catalyst

• CFD simulations of n-Heptane Catalytic cracking

• Extraction of Chromium Ion (VI) Using Bulk Liquid Membrane

• Modeling of the Solubility Drug Material in Supercritical Fluid by New Equation of State

• Modeling of an isothermal and non-isothermal tubular membrane reactor for conversion of synthesis gas to methanol

• Enhancement of photocatalytic activity of ZnO nanoparticles by silver doping with optimization of photodeposition method parameters

• Effect of Seeding Operation on the Dynamic Strength of Urea Prills in Petrochemical Plants

• Multi-objective optimization of Ethane Thermal cracking Reactor using Genetic Algorithm

• Neural Network Approach for Prediction of Asphaltene precipitation and comparison it with Flory-Huggins model in crude oil

• A kinetic study on the catalytic preparation of formaldehyde

• Modeling & Simulation of Superheated water extraction of essential oils from coriander seeds

• Extraction of Clove Buds Essential Oil by Hydrodistillation and Supercritical Fluid

• Thermodynamic Modelling of Solid-Liquid Equilibria for the Solution of Isotactic Poly (1-Butene) in Different Solvents

• Predicting the dew point pressure for gas condensate reservoirs by Esmaeilzadeh-Roshanfekr equation of state

• Bioreactor Design for Liquid Fuel Biodesulfurization

• State of the Art Methodologies in Domino Effect Risk Analysis

• VLE and LLE calculations for binary and ternary mixtures of associating solvents and electrolytes using the SAFT-VR EOS

• Oxidative coupling of methane on SrTiO3 perovskites partially substituted with transition ions

• Comparison of multi-stage condensation with gas permeation process in Vinyl Chloride (VC) recovery by HYSYS simulation

• Excess volumes, excess Permittivity and excess Gibb’s free energy of Halogenated compounds in non-polar solvent at 298.15, 308.15, and 318.15K.

• Full factorial design experiments for investigating the effect of calculated amounts of amino acids on cell density and production of human interleukin-2 in recombinant E.coli BL21.

• Application of wheat bran as a natural adsorbent for removal of Cr(VI) from aqueous solutions

• Modeling of bubble breakage in bubble column reactors

• Development of ANN and SVM models for Prediction of Cell Voltage and Current Efficiency in a Lab Scale Chlor-Alkali Membrane Cell

• Investigation of Membrane Reactor Performance for Naphtha Reforming

• Optimal Grade Transition of a Gas Phase Ethylene Polymerization Reactor

• BTX removal from water pollutants through biological activated charcoal

• Use of soy protein- gum arabic composite as the encapsulant of liquid orange oil emulsion particles

• Numerical simulation of methane-air turbulent diffusion flame using Generalized finite rate approach

• Numerical simulation of laminar flow through converging plates

• Pd nanoparticles–doped LaCoO3 regenerative catalyst for automotive emissions control

• Design of Spiral-Plate Heat Exchanger Using Rapid Design Algorithm

• A new method for Monte Carlo simulation of chain molecules with soft potentials

• Subcritical water extraction of essential oils from Zataria multiflora Boiss.

• Mixing Time, Circulation Time and Liquid Circulation Velocity in a Modified Airlift Loop Reactor with Double Draft Tubes

• Linear electroelastomer roll actuators

• Comparison between Backstepping and Input-Output Linearization Techniques for pH Process Control

• Theoretical simulation and experiments to investigate CO2 & H2S capture from a gas mixture in HFMC & MGA process

• Effect of pore size distribution and temperature on the catalyst tortuosity

• Heat Exchanger Network Area Targeting Considering Stream Passage through Shell or Tubes

• Physicochemical properties of Additive-Gas oil Blends and Their Effects on Performance

• The effect of oxygen addition on the carbon dioxide reforming of methane over Ni/α-Al2O3 catalysts in a fixed bed reactor

• Comparison packed bed and structured packing for optimum operating condition of Natural gas dehydration

• Investigation of the effect of ultrasonic waves on the enhancement of efficiency of direct photolysis and photooxidation processes on the removal of a model contaminant from textile industry

• Volume Reduction of Liquid Nuclear Waste with Evaporation and Mass Transfer Evaluation

• Thermophoretic deposition efficiency of particles in flow along an annular cross-section

• The application of heat pipe for designing uniform temperature batch reactor

• Removal of Lead (II) ions from model milk solution using sour-orange peel: Bioadsorption on a fixed-bed column

• A comparison of biosorptive capacity of loofa-sponge and immobilized Phanerochaete chrysosporium in biosorption of Pb (II) and Cd (II) from aqueous solution

• Photooxidative decolorization of Basic yellow 2 by UV/H2O2 process in an annular photoreactor: Influence of operational parameters and kinetic modeling

• Effect of electrohydrodynamic (EHD) on condensation in presence of non-condensable gas

• Simulation of gas phase Catalytic Oxidation of Benzene on Pt/Al2O3 catalytic monolith using CFD

• Adaptive Sliding Mode Control of a pH Process

• Growth kinetics of sulfur in dilution crystallization from a (sulfur- ethanol –toluene-water) solution

• Application of the Taguchi Method to optimize the process conditions in the production of 2,3-Butanediol by Klebsiella pneumoniae PTCC1290

• Separation of a Propylene-Propane Mixture by a Facilitated Transport Membrane

• Measurement of 1-hydroxy-9,10-anthraquinone and its derivative in supercritical carbon dioxide

• Drying Kinetics and Thermal Properties of Polymer Latex Coating Used in Lost foam Casting

• Analytical Solution for Influence of Yield Stress on Two Phase Stratified Flow through the Pipe

• Performance Analysis of an Aluminum-Cupper Battery for Low Power Applications – An Experimental Study

• Study of the brightener effect on the corrosion behavior of Ni-W-B alloy from tartrate bath by EIS in H2SO4 solution

• Groundwater Contamination Dispersion Modeling

• Assessment of Initial Pressure and Oxygen Concentration Effects on Optimal Temperature Profile in an OCM Plug Flow Reactor and its Performance

• Modeling of Fe/HZSM-5 catalyst deactivation of Fischer-Tropsch synthesis

• Isothermal, isobaric two-phase flash calculations for compositional reservoir simulations

• Experimental Works In Transdermal Drug Delivery Systems

• Adsorption of BTEX from Amine Solution by Activated Carbon

• Identification of the Optimal Pressure Levels in total Site Utility Systems Using Variable Physical Properties

• Study on the liquid-liquid equilibrium containing random copolymer DMAM-TBAM: effects of salt type and temperature and additional polymer

• Characterization of the plus fraction using distribution functions For Iranian gas condensate reservoir

• Preparation of PVDF hollow fiber membrane via thermally induced phase separation (TIPS)

• Investigation on the Rheological and Viscoelastic Properties of Micro and Nano Silica/ Styrene-Butadiene Rubber Composites

• Alternatives for Natural gas Transmission from South-Pars Gas Field to India, NGH, CNG and PNG

• Green Synthesis of New Symmetrical dihydrofuro anthra[2,1-b]furanyl- phosphanylidene acetates as fluorescent Dyes

• Kinetic Studies of Propane Dehydrogenation Over Pt-Sn/Al2O3 Catalyst

• Applicability of osmotic concentration for concentration of alcohols - The effect of operating conditions on flux of Glycerol

• A comparative study for the estimation of drying behavior of pomegranate arils: regression analysis and neural network

• Investigating effects of hydrodynamics in catalytic liquid phase hydrogenation of NDMA through CFD analysis

• Simulation & Control of Fixed Bed Methanol Reforming Reactor

• Relationship between Mechanical Properties and Microstructure of Rigid Polyurethane Foams with Alternative Blowing Agents

• Optimization of Simultaneous Production of Amylase, Pectinase and Cellulase, by Aspergillus oryzae

• The use of a circulating upflow photocatalytic reactor for degradation, mineralization and kinetic study

• Mathematical modeling for adsorption of propane and propylene in zeolite 4A honeycomb monolith

• Application of artificial neural networks for modeling of the absorption of carbon dioxide into aqueous blends of Mono and Diethanolamine with N, N-dimethylethanolamine

• Evaluation of the Presence of Wax-Wax-Liquid (Sα-Sβ-L)

• Kinetics of catalyst deactivation in dehydrogenation of higher normal paraffins over Pt-Sn/Al2O3 catalysts

• OrganicContaminationofTehrangroundwateranditssources

• Intrinsic Kinetics Study of LPDME Process from Syngas over Bi-functional Catalyst

• Modeling the Growth Kinetics of Yeast BBRC- 9026 on Phenol

• Domino Accident Frequency estimation using Monte Carlo Simulation

• ROBUST CONTROLLER DESIGN FOR A CONTINUOUS BIOREACTOR

• Dehydration of methanol to Dimethyl ether employing modified H-ZSM-5 catalysts

• Modeling of Naphtha Reforming Reactors with Deactivation Parameter of Catalyst

• CFD MODELING AND EXPERIMENTAL VALIDATION OF PARTICLE-TO-FLUID MASS AND HEAT TRANSFER IN A RANDOMLY PACKED BED OF CYLINDRICAL CATALYSTS

• CFD investigation of vertical two-phase flow regimes

• Measurement, data analysis and correlation of liquid-liquid equilibria of water + propanoic acid+ 1-octanol system

• Modeling of Gas Condensate Well Performance Using Non-Darcy Flow and Capillary Number Effects by Compositional Method

• Designing a Hierarchical Neural Network Based on Fuzzy Clustering for Fault Diagnosis of the Tennessee-Eastman Process

• Correlations for Shrinkage and Moisture Diffusivity for Drying of Green Peas in a Fluidized Bed with Inert Particles Assisted by Infrared Heating

• Scale Effects on Gas-Solid Fluidized Bed Hydrodynamics

• Thermal Modeling of industrial PVC reactor

• Gas-lift allocation optimization using generalized reduced gradient approach

• Partial Oxidation of Methane to C2-Hydrocarbons: A Thermodynamic Analysis

• Mathematical Modeling and Simulation of Fluorination Reaction of Uranium Dioxide and Evaluation of Existing Gas-Solid Reaction Models

• Recovery of Platinum and Rhenium from the Spent Aromatization Catalyst of Naphta Using the Ion Exchange Method

• Using isothermal kinetic results to estimate the kinetic triplet of catalytically cracking of HDPE

• An experimental & theoretical investigation on thermal performance of a gas-liquid thermosyphon heat pipe heat exchanger in a semi-industrial plant

• Purification of extracellular recombinant xylanase using two-stage polymer-salt aqueous two-phase system

• Gas holdup in a bubble column reactor with different liquid phase properties

• Effect of Inlet Air Cooling by Absorption Chiller and Fog Cooling Method on Gas Turbine Performance

• Modeling and Simulation of an Industrial Continuous Naphtha Catalytic Reformer (CCR)

• CFD Simulation of Liquid Hold-Up in Structured Packed Columns

• SSDR: An Object Oriented Steady-State Data Reconciliation Software

• A new model for the activity coefficients of individual Ions in aqueous electrolyte solutions

• A curing kinetic model of montmorillonite layered silicate nanocomposite

• Modeling and Optimization of the Refinery Steam Network by Pinch Analysis Approach

• Study of Promoting effect of Ruthenium on Homogeneous Iridium-Catalyzed Methanol Carbonylation Process

• Media selection for poly(hydroxybutyrate) production from methanol by Methylobacterium extorquens DSMZ 1338

• Optimization of Cleaning Efficiency of Urea and 1-Propanol for Removal of Biofouling Layer Using Response surface Methodology

• A new correlation and intelligent modeling of asphaltene precipitation in live and tank crude oil systems

• Refolding of recombinant proteins using polymer- salt aqueous two-phase system

• Fuzzy control of fermentation process

• The study of tellurite tolerance and its bioremoval by a halophilic actinobacterial strain, QS-2006

• Design an Optimization of Plate and Frame Heat Exchangers with Rapid Design Algorithm

• Solute Dispersion in Flow through Saturated Porous Media

• Experimental Investigation of pressure drop in concurrent air-water flow

• Improving the Industrial Production of 6- Amino Penicillanic Acid

• Mathematical Modeling of Methane Steam Reforming in Fluidized Bed Membrane Reactor Accompanied by Methane Combustion

• Actinorhodin Production by Streptomyces coelicolor A(3)2

• Modeling of particle size distribution in a gas phase ethylene/propylene copolymerization reactor

• The effect of pore former concentration on properties of Polyethersulfone (PES) /Cellulose Acetate Phthalate (CAP) blend ultrafiltration membranes

• Effect of stripping gas injection in a novel 3-section Desorption column

• Investigating methods and effective parameters in the adsorption of mercury from aqueous solutions

• CFD SIMULATION OF RADIATION SECTION IN ETHYLENE FURNACE

• Numerical Analysis of dissociation enthalpies of simple and mixed hydrates

• Synthesis and color fastness properties of an alkali-clearable azo disperse dye based on naphthalimide

• Numerical investigation of mass transfer in a 90° bend

• Investigation of Urea Thermal Hydrolysis Reactor Performance to Decrease Environmental Pollution

• Simulation of catalytic naphtha reforming with consideration of pressure drop

• Effects of Particle Size Distribution Improvement and Dense Packing Technique on Compressive Strength of Oil Well Cement

• Thermodynamic optimization of Heat Recovery Steam Generators in combined cycle power plant

• Prediction of Dehydration Characteristics of Tarom Garlic slices in Microwave-convection Combination

• Mathematical modeling of garlic cloves drying in a convective dryer

• New Flexible mathematical model to rating an air cooler and comparison by experimental data

• Phase equilibrium for ternary mixtures of (Water + 1-hexanol+ Tert- butly1 alcohol (TBA)) at different temperatures

• A new approach to predict thermodynamic properties of oil

• Dynamic modeling of crude oil fouling in an industrial preheat exchanger of CDU based on artificial neural networks

• Emulsion polymerization of vinyl chloride in batch reactor: Effect of operating variables on the polymerization yield using Taguchi experimental design

• Solubility and diffusional coupling effects on mixed gas transport through glassy polymeric membranes.

• SIMULATION AND OPTIMIZATION OF STEAM NETWORK IN PETROLEUM REFINERIES

• Effect of dehydration component on the performance of bi-functional catalysts in direct synthesis of dimethyl ether from syngas

• Optimization of Distillation Units of Oil Refineries For Maximum Gasoline Production

• A simple one-dimensional model for investigation of heat and mass transfer effects on removal efficiency of particulate matters in a Venturi scrubber

• Dispersion of Solvent in Crude Oil Saturated Porous Media

• Modeling, simulation and control of a tubular fixed-bed dimethyl ether reactor

• CFD Simulation of Power and Mixing Time for a Rushton Turbine in a Baffled-Tank Reactor

• Hybrid Modeling and Control of a Steam boiler System

• Modeling of Catalyst Effect on the Reduction of Barium Sulfate by Methane

• Determination of Pressure Drop in Wire Mesh Mist Eliminator by CFD

• Optimization and performance analysis of dehumidification rotating wheel using solid desiccant

• Separation of Isomeric Xylenes: Experimental and Modeling

• Study of irreversible sorption of CO2 by coal, implications for CO2 storage within coal seams

• Measurement and modeling of solubility of H2S in aqueous Diisopropanolamine solution

• The effect of increment of hydrophilicity on self-cleaning property of membrane

• Evaluation of biodegradability of polyethylene by isolated fungi

• New correlation and intelligent modeling of experimental data of slim tube permeability reduction by asphaltene precipitation in Iranian crude oil reservoirs

• Electroosmotic Flow in PEM Fuel Cells with Variable Zeta Potential

• Ablative performance of resol/ kaolinite nanocomposite

• Photocatalytic degradation of methylene blue in presence of Nanocrystalline TiO2 in aqueous suspension

• Model Predictive Control Using of Local Model Networks: A Case Study

• Derivation of a new cubic equation of state based on partition function for small and large molecules

• Experimental study of fouling mitigation and heat transfer enhancement with wire coil inserts

• Mathematical Modeling of a Membrane Reactor Using Numerical Methods:Comparison of Orthogonal Collocation with Finite Difference

• Thermodynamic Equilibrium Calculations of LPDME Process from Synthesis gas

• preparation of zinc oxide nanoparticles by water solution combustion method

• Experimental Study of non-Newtonian Falling Film Dynamics on Inclined Plate

• Investigation of liquid – liquid equilibria for ternary systems using different thermodynamical models

• Various Types of Microorganisms Applied in Liquid Fuel Biodesulfurization

• Solubility of a solid with an antiseptic property in supercritical CO2

• Application of Taguchi Method in the Optimization of ARC- Carbon Nanotubes Fabrication

• Application of Bayesian Belief Networks in State and Parameter Estimation

• Modeling and Simulation of Methanol Membrane Reactor In Industrial Scale

• Chromium Sorption from Aqueous Solution on Agricultural waste solid (Sawdust)

• Effect of Fracture Geometrical Properties on Oil Recovery by Polymer Flooding: an Experimental Approach

• Propylene Demand from FCC Process an Experimental Investigation at Bench Reactor

• Theoretical Investigation of Replacement of Membrane in Methanol Synthesis Reactor

• Synthesis and Characterization of Water-borne Polyurethane Blended with Chitosan

• Effects of geometrical characteristics on Dry Pressure Drop of the Packed Columns using CFD Analysis

• Turbulent Convective Heat Transfer γ-Al2O3 / Water Nanofluid through Double Pipe Heat Exchanger

• Power-law kinetics of hydrodesulfurization on the commercial CoMo/Al2O3 Catalyst of Tabriz Refinery

• Optimization of fiber orientation in a polymeric composite laminate

• Controlling yield of zeolite NaY synthesis by hydrothermal method

• Effect of volumetric flow rate on axial dispersion coefficient of fluid in liquid-solid bed with RTD curves studies

• Characterization of a Kerosene-derived Rocket Fuel

• Experimental Study of Solvent Flooding to Heavy Oil in Fractured 5-Spot Models: Fracture Geometrical Characteristics Effects

• Comparison of Hydrogen adsorption storage on the carbon adsorbents

• Effects of Injection Constraints on Oil Production from Heterogeneous Reservoirs

• Study of the mixing progress in stirred vessel using ERT

• Vapor - Liquid Equilibrium of (water + Na2SO4 + SC-CO2) System by Equation of State

• Synthesis of submicron alumina powder via a new wet chemical method

• Characterization of Nanocrystalline Titanium Dioxide prepared by precipitation of aqueous TiCl4 solution

• Experimental investigation of turbulent heat transfer of γ-Al2O3/water nanofluid in circular tube

• The effect of the heat loads on the partial-vacuum thermosyphon performance

• Prediction of Viscosities of Binary Gas Mixtures Containing Hydrogen

• Ethylene dichloride (EDC) production unit of Bandar Imam Petrochemical Company simulation

• Wave length effect on Kelvin -Helmholtz instability in oil-gas two phase stratified flow using CFD modeling

• Wave length effect on Kelvin -Helmholtz instability in oil-gas two phase stratified flow using CFD modeling

• VAPOUR RECOVERY DURING FUEL LOADING

• Design and Fluid Flow Analysis of Helix Heat Exchangers

• Study of Shaping a Nickel Perovskite-type Catalyst in the Methane Dry Reforming Reaction

• A Comprehensive Neural Network Model for Predicting Two-Phase Liquid Holdup under Various Angles of Pipe Inclinations

• Effects of Nozzle Diameter, Flow rates and Jet Angel on Mixing Time in a Jet Mixer

• COMPARATIVE STUDY ON SPACE QUALIFIED PAINTS USED FOR THERMAL CONTROL OF A SMALL SATELLITE

• Study Parameters Affecting Size Distribution of Beads Produced from Electro-Spray of High Viscous Liquids

• UV-induced photocatalytic oxidation of an organic dye by prepared nanosized ZnO: Comparison and modeling reaction kinetic

• Dehydrogenation of propane on promoted Pt catalysts supported on different alumina carriers

• A Genetic Algorithm Application for Gas Pipeline Network Optimization

• Co-current and counter-current modes for a membrane dual-type methanol reactor

• Reservoir Connectivity of overlapping ellipsoid sand bodies

• Kinetic Study of the Nickel Oxide Reduction by Methane

• A comparison between different biological methods of nitrogen removal from wastewater

• Modeling and Simulation for industrial ethylene oxide reactors

• An Experimental Study of the Effect of Anionic and Cationic Surfactants on Enhanced Oil Recovery of Aghajari (Iran) Reservoir

• Dynamic Modeling of the Extracted Essential Oil from Spearmint Leaves by Using Supercritical Carbon Dioxide with Neural Network

• Kinetic study of Palladium-Catalyzed Synthesis of vinyl acetate from Ethylene in a Heterogeneous Gas Reaction

• ANALYSIS OF COMBINED CYCLE POWER PLANTS BASE ON PINCH-EXERGY AND THERMOECONOMIC ANALYSIS

• Polymer Brushes in NanoBiotechnology: Applications in Downstream Process

• Pool Boiling Heat Transfer to Alkanolamine Solutions

• Preparation Magnesium chloride particles with controlled morphology and crystalline phase as support of Ziegler- natta’s catalyst

• Quantitive Analysis of Electrospan Nanofibers

• Hydrogen Integration Evaluation between HTGR Power Plants and Oil Refineries

• Investigation the activity and long term durability of a Bi-functional catalyst in direct DME Synthesis

• Adaptive Feedback Linearization Control of pH

• Analysis of Whole Range of Flux Behavior during Full Scale Apple Juice Ultrafiltration Process

• Asphaltene identification using intermolecular potential energy and nanostructural forces

• Experimental and CFD studies on the effect of the jet’s position on mixing

• Simulation of Tubular Solid Oxide Fuel cell with Natural Gas Fuel

• Catalytic Combustion of Biogas in a Packed Bed Reactor

• The Study of Lead Adsorption from Aqueous Solution by Carbon Nanotubes (CNTs): Adsorption Equilibrium and Kinetics

• CFD modeling of heat transfer from a radiant heater

• Effect of Upscaling Method on Recovery Performance Prediction of Two-Phase Flow through Porous Media

• Modeling of fixed bed reactor for selective dehydrogenation of heavy paraffins

• Modeling of non-catalytic gas-solid reactions- Multicomponent nonequimolar counterdiffusion of gaseous phase

• Revamping of Merox LPG sweetening unit for deeper desulfurization

• Numerical simulation of multiphase flow in bubble column

• Modeling the steady-state and dynamic V-I characteristics of PEM fuel cell

• Starch ester synthesis: effect of pH on the preparation of succinate corn starch

• Modeling and simulation of Catalytic Reforming of Magnaformer of Bandar-Imam Petrochemical Complex

• Acid Gas Permeation Behavior in Polymeric Membranes

• Combined Water and Thermal Pinch Analysis in Pulp and Paper Industries

• CALCULATION OF EQUILIBRIUM FLAME TEMPERATURE AND COMPOSITION FOR GASEOUS FUELS COMBUSTION USING THE MINIMISATION OF GIBB`S FREE ENERGY METHOD

• Synthesis of nano zirconia powders by sucrose as a chelating agent and template material and their applications for CH4/CO2 reforming

• CFD Simulation of an internal loop airlift bioreactor

• Continuous screening, an efficient method for the isolation of oil degrading bacteria from oily sludge

• A General View on the Effects of Iodide salts in Iridium Catalyst in Methanol Carbonylation Process

• Practical Study of VOCs Emission from External Floating Roof Tanks

• CFD Simulation of Combustion inside an Industrial Furnace

• Modeling the Effect of EGR on Combustion and Pollution of Direct Injection Diesel Engines with Flow Field Model

• Experimental and theoretical investigation of drying of a solid particle in an inert medium fluidized bed assisted by infrared radiation

• Two Dimensional Simulation of the Steam Reforming Unit of Methanol Plant

• Experimental-Based Numerical Simulation of Two Phase Flow through Porous Media: Comparison of Finite Element and Finite Difference Schemes

• Mercury removal by loofa-immobilized Phanerochaete Chrysosporium

• Hydrodynamics of Bubbling Fluidized Bed by Computational Fluid Dynamics

• THERMODYNAMIC OPTIMIZATION OF THE SOLAR PARABOLIC COOKERS AND COMPARISON WITH ENERGY ANALYSIS

• Synthesis of mesoporous nanocrystalline γ-Alumina by sol-gel method with using cationic surfactant

• Characterization and catalytic properties of LaMoxV1-xOn perovskites for direct formation of Acetic acid from Ethane

• RFCC Spent Catalyst as a High Quality Complementary Cementitious Material

• INVESTIGATION OF HYDRODYNAMICS, HEAT AND MASS TRANSFER SIMULTANEOUSLY IN LIQUID FILM FLOW ON INCLINED PLATES USING CFD APPLICATION

• Modeling and simulation of coke deposition in transfer line exchanger (TLE) of olefin plant

• Effect of baffle arrangement on turbulent flow field in a stirred tank

• Numerical simulation of mass transfer in falling film with FEM approach

• Hydrogenation of nitrobenzene over nano-sized Pd/γ-Al2O3 catalyst

• CFD simulation of Non Porous Catalytic Reactor for the Decomposition of Ammonia

• Dynamic simulation of the Fischer–Tropsch synthesis in slurry bubble column reactors

• Fuzzy corrosion modeling, new horizons, new opportunities

• Simulation of Dual Porosity Model for Naturally Fractured Reservoirs

• Formation Damages; Prevention Method and Remedies

• CFD Simulation of Notched-Trough Liquid Distributor in Packed Columns

• Optimizing a typical crude oil desalting plant by experimental dsign approach

• Effects of Fuel Prereforming on the Performance of a Solid Oxide Fuel Cell

• Preparation and evaluation of gelatin nanoparticles by modified coacervation method as drug delivery systems

• Study of the catalyst deactivation in DME synthesis from methanol dehydration

• Investigation of Cadmium Sorption from Aqueous Solution on Sawdust

• Statistically Simulating Of Hydrodealkylation Reactors

• Effects of Process Variables On The Dispersion of Carbon Nanotubes in Polycarbonate Matrix

• Synthesis of Metal Oxide Nanopowders via Polyacrylamide Gel Method: Influence of Precursors

• Theoretically Estimation of (+)-catechin solubility in different solvents

• Fuzzy Sliding Mode Control Approach for Nonlinear Chemical Processes

• Co-culture of human skin keratinocytes and melanocytes on a novel biodegradable scaffold

• Heat Exchanger Network Retrofit by Pinch Technology on Reformer Area of Aromatics Plant

• Viscosity Build up through Component Interactions in Synthetic-Based Drilling Fluids

• Eulerian Modeling of a Circulating Fluidized Bed, including Mean Particle Diameter

• Optimization of MEOR process conditions in Iran’s Ahwaz oil reservoirs

• Synthesis and Performance of Tubular NaA zeolite membrane

• The effect of orientation and fiber length on the modulus of natural fiber reinforced composites

• Production of sulfur nanocrystal through dilution crystallization

• Studies on the ZSM-5 Zeolite Synthesis Using Chelating Agent: Influence of Crystallization Temperature and Time

• Effects of alkali and alkali-earth metals in catalyst of methane reforming

• LDPE/EPDM Blends with Unique Surface, Electrical and Mechanical Properties for Electrical Insulators

• Numerical Analysis of the Motion and Vaporization of the Droplets in a Cement Plant Gas Conditioning Tower

• CFD model for turbulent and laminar boundary layer momentum and heat transfer on a flat plate

• Shape Memory Effect of Polyurethane/Polycaprolactone (PU/PCL) Blend Based on Melting Temperature of PCL

• Fabrication and Characterization of Multilayer α-Alumina NF Membranes

• Hydrodynamic Modeling of Gas-Phase Olefin Polymerization Reactors Using CFD

• Energy Cost Minimization and Data Reconciliation

• Coarse Grid Generation Based on Vorticity for Reservoir Flow Simulation: Extension to Unstructured Grid

• Simulation of oxygen and glucose transport in hollow fiber membrane bioreactor for growing artificial tissue

• Object-Oriented Design for System Identification and Its Application in Chemical Industries

• HYDROGEN PRODUCTION BY ENRICHMENT GRANULES IN AN ACIDOGENIC FERMENTATION PROCESS

• Flammability of kaolinite layered silicate/ phenolic resin/ asbestos cloth nanocomposite

• Electrical conductivity of carbon black/ poly (ethylene terephthalate)/polypropylene composite

• Production of polypyrrole composites using various surfactants in aqueous media

• synthesis of silver nanowires with adjustable diameters

• Analysis of a refrigeration cycle driven by refrigerant Steam turbine

• Studing the characterization of polyaniline and polypyrrole films

• Well Spacing and Recovery Optimization of One of the Iranian Oil Fields by Using Streamline and Reservoir Simulation

• Study of the deactivation condition of nickel catalyst used in Arak and Razi petrochemical complex